from the garden hose and position it for final installation. 4. Turn off main source water supply prior to installation. 5. Install the unit to the main water supply using the supplied components. Do not over tighten fittings, as this may cause leakage and broken
E. Water Supply Requirements (1) The supply water should be clean. Dirty water may cause trouble in unit water line. (2) Water Pressure More than 0.1Mpa(1.0kg/ ) water pressure in utility section is required for operating unit efficiently at any time. F. Electric
DIMENSIONS AND INSTALLATION INFORMATION IN INCHES Specifiion Revised 2/20 Listed by Underwriters Laboratories with wash water for clean, bright, soft-to-the-touch results Cycle status lights – Easily see where your load is in the cleaning
If the cold water shut off valve can not turn off the water, the main water supply to the house must be shut off for the installation. Another option is to use a “self piercing saddle valve” from APEC or from a local hardware store. 2.
Use the links below to find and download any Waterstone product installation guide or spec sheet. For smaller replacement parts such as diverters, cartridges or o-rings, click here. If you do not find what you are looking for, contact our technical support department in the USA: 1-888-304-0660.
Molded Coolant Hose Identifiion Guide This guide can be used to identify molded coolant hoses by dimensions, including interior dimension, center line length and row nuer, and photographs. Accessory Belt Drive Hardware Kit Appliion Listing Fina a
Route water supply line into installation area. IMPORTANT: Incoming hot water temperature should be at least 120 F (49 C). Do not use the furnished drain hose or a rubber garden hose for the water supply line. Either of these hoses can burst. Flooding may 3.
Sydney Water – Water meter installation guide Document current at March 2018 Page 4 1. Introduction This guide explains what you need to know about installing a water meter on a property. This is so we can: • read and exchange the meter in future • charge
DIMENSIONS AND INSTALLATION INFORMATION IN INCHES Specifiion Revised 2/20 Listed by Underwriters Laboratories with wash water for clean, bright, soft-to-the-touch results Cycle status lights – Easily see where your load is in the cleaning
3 LOION REQUIREMENTS Proper installation is your responsibility. You will need: n A water heater set to 120 F (49 C). n A grounded electrical outlet loed within 6 ft. (1.8 m) of power cord on back of washer. n Hot and cold water faucets loed within 4 ft. (1.2 m) of hot
4 EATON Synflex Hose and Fittings Master alog E-HOOV-MC001-E2 October 2013 HYDRAULIC Air Tools HOSE GENERAL INFORMATION AIR 3130 & WATER HOSE & T U B ING T RUCK H OSE AEROUIP/POLYON FITTINGS AEROUIP/TTC FITTINGS
Installation Steps Step #1 – turn off power to the dishwasher Step #2 – shutoff the water shutoff valve and place a towel underneath Step #3 – Using 5/8″ crescent wrench, disconnect the water supply hose from the shutoff valve; let water drain out (won’t be much)
Hose and Connector Installation Guide 6 (2) Permanent Crimped Hose Assely: The permanent coupling (1E2115) consists of a head, stem, and shell, shown below. a. Threaded Coupling b. Snap to Connect Coupling c. Flange Coupling.i. Code 61
rough-in dimensions BeFore insTALLATion WAshLeT® eXTension hose KiT insTALLATion mAnuAL Follow these instructions and follow all safety procedures. See the Washlet installation manual for additional safety precautions. incLuded PArTs Make sure you
4 EATON Synflex Hose and Fittings Master alog E-HOOV-MC001-E2 October 2013 HYDRAULIC Air Tools HOSE GENERAL INFORMATION AIR 3130 & WATER HOSE & T U B ING T RUCK H OSE AEROUIP/POLYON FITTINGS AEROUIP/TTC FITTINGS
Zodi Product Specs, Product Instructions, Videos and More relating to Zodi''s Outdoor Comfort products. Check our products out. If you are looking for product comparison page, click here. Click here to download the complete alog of all product spec sheets
High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of 1/ 4” may be used. A shut-off valve installed outside dishwasher cabinet is best. 8. Route water supply line into installation area. 9. Stand dishwasher back upright
Installation Instructions PREPARE HOT WATER LINE † The line may enter from either side, rear or floor within the shaded area shown in Figure F. † The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2” dia
PROPER INSTALLATION This washer must be properly installed and loed in accordance with the Installation Instructions before it is used. v Ensure that the hot water hose is connected to the “H” (internal red screened) valve and the cold water hose
DIMENSIONS AND INSTALLATION INFORMATION IN INCHES Specifiion Revised 2/20 Listed by Underwriters Laboratories with wash water for clean, bright, soft-to-the-touch results Cycle status lights – Easily see where your load is in the cleaning
NOTE: The Camco Heated Drinking Water Hose is self-regulating and does not require a thermostat. It automatically adjusts its power consumption based on the temperature that it is exposed to. SafeguardS: 1. Read and understand all instructions before use. 2.
Molded Coolant Hose Identifiion Guide This guide can be used to identify molded coolant hoses by dimensions, including interior dimension, center line length and row nuer, and photographs. Accessory Belt Drive Hardware Kit Appliion Listing Fina a
ROUGHING-IN INSTALLATION Kohler reserves the right to change marked dimensions without prior notice. Fig.#1 Unit:mm 183 400 440 370 775± 10 224 420 155 366 275 358 650 185 P TRAP 260 S TRAP 1. REMOVE EXISTING TOILET Turn off water supply.
3 SPECIFIIONS Model WHELJ1 Rated Service Flow Rate 6.0 gpm (22.7 L/min.) Pressure Drop at Rated Service Flow 10 psig*(68.9 kPa) Pressure Drop at 9.6 gpm 15 psig*(103.4 kPa) Water Pressure Limits (minimum / maximum) 30 - 125 psi (206.8 - 861.8
Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to avoid clogs. Water should run until clear. Make note of which hose is connected to hot water to help in attaching hoses to washer correctly. Attach hot water hose to hot water