chemical hose testing standards catalogue

API | Standards

API was formed in 1919 as a standards-setting organization and is the global leader in convening subject matter experts across segments to establish, maintain, and distribute consensus standards for the oil and gas industry. In its first 100 years, API has

J517: Hydraulic Hose - SAE International

Hydraulic Hose J517_201302 This SAE Standard provides general, dimensional and performance specifiions for the most common hoses used in hydraulic systems on mobile and stationary equipment. The general specifiions contained in Sections 1 through 12 are applicable to all hydraulic hoses and supplement the detailed specifiions for the 100R-series hoses contained in the later sections

Hose Handbook March 2003 - Hose Fittings - Hydraulic Hoses

This Hose Handbook has been compiled to provide authoritative information on materials, constructions, tolerances, appliions, fittings, storage, care and maintenance of hose. This Handbook will help users to make an intelligent selection of hose for various

DNVGL-CP-0183 Flexible hoses - Non-metallic materials - Rules and standards …

Section 1 Class programme — DNVGL-CP-0183. Edition Deceer 2015 Page 6 Flexible hoses - Non-metallic materials DNV GL AS 1.4 Definitions Table 1 Definitions hose assely final product, complete and ready for service” i.e. a flexible non-metallic hose

Storage, treatment, inspection procedure for hoses | …

Frequent testing at a too high test pressure is destructive and can result in the connection between the inlays and the hose being broken. The pressure test must take place with water with the hose outstretched. Allow the pressure to increase to 1.5 times the

INDUSTRIAL HOSE CARE & MAINTENANCE Agricultural, …

unloading, LPG transfer, in plant chemical use, etc.). ‘M’ Material Conveyed Air, water, the specific chemical, product or material burst testing of the hose is suggested to assess remaining hose strength as well as the mode of failure. This data is useful to

ASTM International - Standards Worldwide - 94(2020) …

D380-94(2020) Standard Test Methods for Rubber Hose Test Specimens~ 2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard. ASTM Standards D412 Test Methods for Vulcanized Rubber and Thermoplastic ElastomersTension

SPECIFIION GUIDANCE FOR DOCK HOSES

SPECIFIION GUIDANCE FOR DOCK HOSES CONTENTS PAGE Reference Documents 1 Appliion 1 Introduction and Purpose 2 Scope 2 PART I SPECIFIION 4 1.0 Standards and Practices 4 2.0 Appliion of BS EN Standards 5 3.0 Hose

Chemical Resistance | Durapipe UK

This Chemical Resistance Guide covers all of the products in the Durapipe product range, with most of the data based on laboratory exposure testing. The effect of exposure is usually determined by appearance and change to physical properties of the test piece.

Hose & Coupling Reference Guide

erpillar''s superior hose construction and testing differentiates it from other manufacturers. erpillar was the first to design and manufacture high pressure hydraulic hose known throughout the industry as XT hose. XT hose standards far exceed industry today.

Fire Hose Testing Standard Operating Guidelines

SAFETY FIRST FIRE HOSE TESTING - SOG''s - Page 2 of 2 11. With the air bleeder open, the pressure shall be raised gradually to 45 PSI (± 5 psi) (3.1 bar ± 0.35 bar or 310 kPa ± 35kPa) 12. After the hose test layout is full of water, all the air in each hose line

Chemical Resistance Table - Parker Hannifin

TH17 alogue 4401/UK Technical Handbook Technical Handbook The following table is essentially based upon the most updated technical data available, on information from raw material suppliers, as well as some International Standards, e.g. ISO TR 7620, EN

BG4-2004 Flexible hoses standard - Hydraquip

alogue data shall quote both the overall length between sealing faces (or equivalent) and the active length of the hose. The active length of the hose is defined as the minimum length between the ferrules. Note that hose tail and ferrule may not end at the same

Industrial Chemical Standards - ASTM International

ASTM''s industrial chemical standards are instrumental in the testing and evaluation of the physical and chemical properties of substances used or produced primarily in industrial appliions, particularly in automotives. These chemicals, both organic and inorganic

INDUSTRIAL HOSE CARE & MAINTENANCE Agricultural, …

unloading, LPG transfer, in plant chemical use, etc.). ‘M’ Material Conveyed Air, water, the specific chemical, product or material burst testing of the hose is suggested to assess remaining hose strength as well as the mode of failure. This data is useful to

Hose & Coupling Reference Guide

erpillar''s superior hose construction and testing differentiates it from other manufacturers. erpillar was the first to design and manufacture high pressure hydraulic hose known throughout the industry as XT hose. XT hose standards far exceed industry today.

HOSE MASTER

hose is to be installed. When determining chemical compatibility, it is important to know the temperature and concentration of the chemical(s). Although there are many resources to confirm chemical compatibility, two of the industry standards that you may

Hose Handbook March 2003 - Hose Fittings - Hydraulic Hoses

This Hose Handbook has been compiled to provide authoritative information on materials, constructions, tolerances, appliions, fittings, storage, care and maintenance of hose. This Handbook will help users to make an intelligent selection of hose for various

Reference standards - British Pharmacopoeia

Reference standards Overview British Pharmacopoeia chemical reference substances (BPCRS) are primary standards. We establish these using absolute methods and the declared content figures are determined without comparing to another

HYDRAULIC HOSE FITTINGS & ADAPTERS - ALFAGOMMA

inspection, testing and replacement of hose asselies before failure occurs; taking into account factors including: severity of appliion, frequency of equipment use, past performance of hose asselies. Document your maintenance, inspections and testing.

BG4-2004 Flexible hoses standard - Hydraquip

alogue data shall quote both the overall length between sealing faces (or equivalent) and the active length of the hose. The active length of the hose is defined as the minimum length between the ferrules. Note that hose tail and ferrule may not end at the same

Fire Hose Testing Standard Operating Guidelines

SAFETY FIRST FIRE HOSE TESTING - SOG''s - Page 2 of 2 11. With the air bleeder open, the pressure shall be raised gradually to 45 PSI (± 5 psi) (3.1 bar ± 0.35 bar or 310 kPa ± 35kPa) 12. After the hose test layout is full of water, all the air in each hose line

SPECIFIION GUIDANCE FOR DOCK HOSES

SPECIFIION GUIDANCE FOR DOCK HOSES CONTENTS PAGE Reference Documents 1 Appliion 1 Introduction and Purpose 2 Scope 2 PART I SPECIFIION 4 1.0 Standards and Practices 4 2.0 Appliion of BS EN Standards 5 3.0 Hose

API | Standards

API was formed in 1919 as a standards-setting organization and is the global leader in convening subject matter experts across segments to establish, maintain, and distribute consensus standards for the oil and gas industry. In its first 100 years, API has

Hose Inspection & Hose Testing | Buckley Indutrial

Hose inspection & testing hyDROSTATIC TESTING Simply put, Hydrostatic Testing involves filling a hose assely with water and taking it to a pre-specified test pressure, generally 1.5 times the maximum working pressure and holding it for a set period of time.