sae hose clamp standard manufacturer

Everbilt 3/8 - 7/8 in. Stainless Steel Hose Clamp-6760595

Ideal - 3/8-7/8 in. Hose Repair Clamp - Fits 3/8-7/8 in. hoses. Complements hoses made from various materials. Classic stainless steel finish. - THD SKU# 100575

Ideal Hose Clamp Size Chart | Garage Sanctum

Ideal Hose Clamp Size Chart. Here you can see ideal hose clamp size chart. The table shows the two main elements. The first one is the diameter range and the second is types available. In the diameter range you can see size, minimum and maximum for inches and millimeters. In the types available, you can see standard, all stainless and silicone

Hose Clamp Manufacturer, SS Hose Clamp Supplier

It is the only standard that employs a pressure test and is globally considered as the strictest Standard for a hose clamp in the world. To have the Kitemark™ the hose clamps must as well pass independent testing. On the other hand, SAE Standard J1273 is an American standard. It provides guidelines for selection, routing, manufacturing

Hose Clamps - Fastener Mart

Standard series hose clamps are the most common and are found in vehicle and industrial appliions. Minimum clamp diameter is 3/8" and the typical maximum is about 8 7/16". They have 1/2" wide bands and 5/16" slotted hex head screws.

Hose Clamp Manufacturer, SS Hose Clamp Supplier

It is the only standard that employs a pressure test and is globally considered as the strictest Standard for a hose clamp in the world. To have the Kitemark™ the hose clamps must as well pass independent testing. On the other hand, SAE Standard J1273 is an American standard. It provides guidelines for selection, routing, manufacturing

Hose Clamp - Standards Search | Engineering360

Feb 01, 2019· This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. Purpose This document is compiled for the specific purpose of describing the basic characteristics and …

Hose clamp, Collar clamp - All industrial manufacturers

Worm-Drive Hose Clamp - 68.0 - 73.0 mm | 2.677 - 2.874 in Inside Diameter, 24.0 mm | 0.945 in Band Width Slip-On Item code: 494338 276 In stock Stainless Steel T-Bolt Hose Clamp Compare this product Remove from comparison tool

MPC® worm gear clamps | MPC® Industries

The U-Seal 8 hose clamp is a SAE Type M with closed band. Anchoring the house to the full band results in higher torques than usual for this type of hose clamp. U-Seal 8 is usually applied in smaller hose asselies like fuel hoses, laboratory hoses or small vacuum or duct hoses.

Hose Clamps, Standard, Partial Stainless - Fastener Mart

Standard Hose Clamps, Partial Stainless Steel. Worm-Drive Hose Clamps are used to fasten hoses and tubes to fittings and pipes. A captive screw tightens and releases the band. The only tool needed is a screwdriver or hex driver. Size is based on clamp diameter range and may also be specified as an SAE …

HOSE CLAMPS CLAMP SYSTEMS - Pirtek Australia

HOSE CLAMPS CLAMP SYSTEMS 1 M WORM DRIVE CLAMPS 2 Technical Description 2 Complies with US/SAE Standard J1508 304 Stainless Steel band and housing with 305 Stainless Steel screw. 240 hour corrosion resistance in salt spray test Materials: All solid band clamps conform to DIN 3017

Seachoice Hose Clamp Set in Stainless Steel-23501 - The

6 in. x 2-1/2 in. Quick Release Bar Clamp with 12 in. Spreader The POWERTEC 71088 6 x 2-1/2 Quick-Release The POWERTEC 71088 6 x 2-1/2 Quick-Release Bar Clamp and 12 Spreader is your essential clamping solution when gluing or asseling your smaller scale woodworking and crafting projects, as well as in a vast array of other appliions. Easily grip your stock via the handy ratcheting trigger

Engineering Essentials: Types of Hydraulic Hose

The SAE standards. SAE answers those questions with its J517 hydraulic hose standard. This hose standard serves as the most popular benchmark in the realm of industrial hydraulics today. More specifically, J517 is a set of guidelines that applies to the current SAE 100R series of hoses.

Hose clamp - 3D CAD Models & 2D Drawings

The US Army TACOM maintains Commercial Item Description (CID) A-A-52506 that provides for the standardized acquisition of hose clamps by the Department of Defense; the CID references the SAE specifiions. The CID superseded Federal Specifiion WW-C-440 for hose clamps in 1994. See also. Band clamp; Jubilee Clip; Marman clamp

SAE J1508 - Hose Clamp Specifiions | Engineering360

This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. Purpose. This document is compiled for the specific purpose of describing the basic characteristics and minimum performance requirements recommended by the manufacturers.

SAE 12, 1/2"-1-1/4" Dia, 1/2" W, Worm Drive Hose Clamp

The branding detaches from the housing so you can install and remove these clamps without disconnecting the hose or tube. Not recommended for use with silicon (soft) hose or tube. They are manufactured in compliance with ANSI/SAE J 1670 recognized standard, entitled "Type F clamps for pluing appliions".

American Standard Hose Clamps : Bel-Metric, Metric

General purpose automotive and industrial clamps. High strength 4-piece Quadra-Lock construction. Exceeds all SAE requirements. Use for all standard clamp appliions. 12.7mm (1/2") Band and 7.9mm (5/16") slotted head hex screw. Per SAE standard J1508 Type "F"

Constant Tension Spring Hose Clamps - Auveco

S.A.E. Standard. J1508 (6) Used with. 20902 (4) Width. 15MM (19/32 Clamps > Constant Tension Spring Hose Clamps; Constant Tension Spring Hose Clamps. Constant Tension Band Hose Clamps. For Heater & Radiator Hoses; 1074 Spring Steel; Black OEM Finish; Conforms To SAE J1508 & GM 6298M; Rated At 30 P.S.I. Display Type Results per Page

Stainless Steel Hose Clamps - 1/2" Band, SAE Size 6-24

Stainless steel clamps are ideal for use in harsh, corrosive environments such as automotive, marine, pluing, swimming pools, and agricultural. Available in a SAE sizes 4-56 and can be tightened to diameter sizes ranging from 5/8" to 4". Find a hose clamp that will let you work with confidence with one of our high quality stainless steel clamps.

Hose clamp, Collar clamp - All industrial manufacturers

Worm-Drive Hose Clamp - 68.0 - 73.0 mm | 2.677 - 2.874 in Inside Diameter, 24.0 mm | 0.945 in Band Width Slip-On Item code: 494338 276 In stock Stainless Steel T-Bolt Hose Clamp Compare this product Remove from comparison tool

Hose Clamps (J536 Ground Vehicle Standard) - SAE Mobilus

Fasteners Committee The Fasteners Committee is dedied to serving the users of fasteners by identifying the need for and developing and maintaining Standards, Recommended Practices and Information Reports in the area of fasteners (including nuts, bolts, washers, screws, pins, rivets and other fasteners) for use with various Land-Sea vehicular appliions.

Koehler 3/4in to 1 3/4in Hose Clamp 2 Pack

Clamp diameter range 3/4 In. to 1-3/4 In. Type F SAE hose clamp exceeds SAE standard J1508. 300 series 1/2 In. stainless steel band, plated carbon steel housing and screw. Replaces original equipment hose clamps.

Spring Hose Clamps | McMaster-Carr

These clamps have a wider band than other constant-tension clamps, which provides more coverage and reduces the chance of leaks.. The spring-action band lets the clamps automatically expand and contract with your hose or tube as temperatures fluctuate. Clamps are for firm plastic and rubber hose and tube. They are zinc-plated steel for fair corrosion resistance.

Hose Clamps (J536 Ground Vehicle Standard) - SAE Mobilus

Fasteners Committee The Fasteners Committee is dedied to serving the users of fasteners by identifying the need for and developing and maintaining Standards, Recommended Practices and Information Reports in the area of fasteners (including nuts, bolts, washers, screws, pins, rivets and other fasteners) for use with various Land-Sea vehicular appliions.

Ideal Hose Clamp Size Chart | Garage Sanctum

Ideal Hose Clamp Size Chart. Here you can see ideal hose clamp size chart. The table shows the two main elements. The first one is the diameter range and the second is types available. In the diameter range you can see size, minimum and maximum for inches and millimeters. In the types available, you can see standard, all stainless and silicone

Hose Clamp - Standards Search | Engineering360

Feb 01, 2019· This SAE Standard covers thirty-two (32) types of clamps most commonly and suitably being used on OEM coolant, fuel, oil, vacuum, and emission systems. Purpose This document is compiled for the specific purpose of describing the basic characteristics and …