Our comprehensive line includes low pressure, medium pressure and high pressure pneumatic and hydraulic hoses that are resistant to heat, ozone, weather, chemicals, oil, flames, UV and abrasion. Parker is the largest hose manufacturer in the world and provides an engineered solution to all of your hose product needs.
High Pressure Hex Connections (48) JIC Hex Connections (44) Medium Pressure Collars (5) Medium Pressure Gland Nuts (5) Medium Pressure Hex Connections (172) Needle Valves (33) NPT Hex Connections (316) Plugs (29) Quick Couplers (26) (6) (10) (39)
30 CFR §56/57.13021 High-pressure hose connections. Except where automatic shutoff valves are used, safety chains or other suitable locking devices shall be used at connections to machines of high-pressure hose lines of ¾-inch inside diameter or larger, and between high-pressure hose lines of ¾-inch inside diameter or larger, where a connection
20K Needle Valves - Medium Pressure Thread Our Standard Needle Valves with Medium Pressure Thread connections rated for working pressures up to 20,000 psi. Available in 2-Way Straight, 2-Way Angle, 3-Way Two Inlet, 3-Way Two Outlet, 2-Stem Manifold
OSHA Regulations Standards - 29 CFR, 1910.242 (partial): (b) Compressed air used for cleaning - Compressed air shall not be used for cleaning purposes except where reduced to less than 30 PSI and then only with effective chip guarding and personal protective
OSHA Regulations Standards - 29 CFR, 1910.242 (partial): (b) Compressed air used for cleaning - Compressed air shall not be used for cleaning purposes except where reduced to less than 30 PSI and then only with effective chip guarding and personal protective
with high-pressure compressed air (such as a plastic water hose) can easily burst or break in two, causing one end of the hose or tube to whip around and strike you or a co-worker. It is also of upmost importance that the clamps and similar fittings we use to connect
Material to be conveyed — The hose, including the hose tube and cover, along with the couplings and O-rings, must be compatible with the type of fluid being conveyed. Pressure — Know the system pressure, including pressure spikes. The hose’s published
with high-pressure compressed air (such as a plastic water hose) can easily burst or break in two, causing one end of the hose or tube to whip around and strike you or a co-worker. It is also of upmost importance that the clamps and similar fittings we use to connect
Medium Pressure Medium pressure products are well suited for low to medium under pressure and lighter materials such as wood shavings, chips, dust and other particles. The duct system is available in different materials, thicknesses and connections.
High Pressure to MPI Tube Stub ..Page 12 X47HT7 Medium Pressure Port Connector to MPI Tube Stub .. Page 12 X42HT7 Medium Pressure to MPI Tube Stub ..Page 13 T7HOA MPI Tube Stub to Male SAE O-ring M40HT7
HIGH PRESSURE FITTINGS SPIR STAR High Pressure fittings seal with a 60 degree cone and are rated for working pressures up to 60,000 psi. Sizes: Common Description Actual Thread Dimension 1/4” High Pressure 9/16”-18 Thread on
Our comprehensive line includes low pressure, medium pressure and high pressure pneumatic and hydraulic hoses that are resistant to heat, ozone, weather, chemicals, oil, flames, UV and abrasion. Parker is the largest hose manufacturer in the world and provides an engineered solution to all of your hose product needs.
The medium pressure series uses Parker Autoclave Engineers medium pressure connection. This coned-and-threaded connection features orifice sizes to match the high flow characteristics of this series. Pressures to 20,000 psi (1379 bar) Medium Pressure
High-pressure hose connections Except where automatic shutoff valves are used, safety chains or other suitable locking devices shall be used at connections to machines of high-pressure hose lines of 3/4-inch inside diameter or larger, and between high-pressure hose lines of 3/4-inch inside diameter or larger, where a connection failure would create a hazard.
A low-pressure component, hose or fitting should not be incorporated into a high-pressure system. Component, hose or fitting ruptures are likely to occur. Pressure relief valves incorporated into the hydraulic system will avoid pressure buildups during use.
A low-pressure component, hose or fitting should not be incorporated into a high-pressure system. Component, hose or fitting ruptures are likely to occur. Pressure relief valves incorporated into the hydraulic system will avoid pressure buildups during use.
High Pressure Fittings Complete range of elbows, tees, and crosses for all pressure classes and tubing connections Constructed of high tensile 316 stainless steel Full line of union couplings, bulkhead couplings, caps, line filters, ball check valves, soft seat check
High Pressure to MPI Tube Stub ..Page 12 X47HT7 Medium Pressure Port Connector to MPI Tube Stub .. Page 12 X42HT7 Medium Pressure to MPI Tube Stub ..Page 13 T7HOA MPI Tube Stub to Male SAE O-ring M40HT7
HIGH AND MEDIUM PRESSURE COMPRESSED AIR PIPING 04/06 PART 1 GENERAL 1.1 REFERENCES 1.2 RELATED REQUIREMENTS 1.3 SUBMITTALS 1.4 QUALITY ASSURANCE 1.4.1 Equipment Data
20K Needle Valves - Medium Pressure Thread Our Standard Needle Valves with Medium Pressure Thread connections rated for working pressures up to 20,000 psi. Available in 2-Way Straight, 2-Way Angle, 3-Way Two Inlet, 3-Way Two Outlet, 2-Stem Manifold
There is a similar standard in Subpart P of the OSHA General Industry standards at 1910.243(b)(2), which states that “Hose and hose connections used for conducting compressed air to utilization equipment shall be designed for the pressure and service to”.
Health and Safety Executive Safety requirements for pressure testing Page 3 of 9 Test hose failure 22 Test hoses can also deteriorate, leading to release of fluid. This often occurs from incorrect lengths of hose being used, where bend radius is too small, or hoses
All connections shall be equipped with safety lashings. 20.A.17 Connections with high pressure hoses must be secured with a safety lashing/whip check. Canadian Centre for Occupational Health & Safety: Make sure that hose connections fit properly and are equipped with a mechanical means of securing the connection (e.g., chain, wire, or positive locking device).
High Pressure to MPI Tube Stub ..Page 12 X47HT7 Medium Pressure Port Connector to MPI Tube Stub .. Page 12 X42HT7 Medium Pressure to MPI Tube Stub ..Page 13 T7HOA MPI Tube Stub to Male SAE O-ring M40HT7